/*********************************************************************
*
* Microchip USB C18 Firmware Version 1.2
*
*********************************************************************
* FileName: io_cfg.h
* Dependencies: See INCLUDES section below
* Processor: PIC18
* Compiler: C18 3.11+
* Company: Microchip Technology, Inc.
*
* Software License Agreement
*
* The software supplied herewith by Microchip Technology Incorporated
* (the 鼎ompany・ for its PICmicroｮ Microcontroller is intended and
* supplied to you, the Company痴 customer, for use solely and
* exclusively on Microchip PICmicro Microcontroller products. The
* software is owned by the Company and/or its supplier, and is
* protected under applicable copyright laws. All rights are reserved.
* Any use in violation of the foregoing restrictions may subject the
* user to criminal sanctions under applicable laws, as well as to
* civil liability for the breach of the terms and conditions of this
* license.
*
* THIS SOFTWARE IS PROVIDED IN AN 鄭S IS・CONDITION. NO WARRANTIES,
* WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED
* TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
* PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. THE COMPANY SHALL NOT,
* IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL OR
* CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
*
* Author Date Comment
*~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
* Rawin Rojvanit 11/19/04 Original.
* Rawin Rojvanit 05/14/07 Added pin mapping for PIC18F87J50
* FS USB Plug In Module board.
********************************************************************/
#ifndef IO_CFG_H
#define IO_CFG_H
/** I N C L U D E S *************************************************/
#include "autofiles\usbcfg.h"
/** T R I S *********************************************************/
#define INPUT_PIN 1
#define OUTPUT_PIN 0
#if defined(PIC18F4550_PICDEM_FS_USB)
/** U S B ***********************************************************/
#define tris_usb_bus_sense TRISAbits.TRISA1 // Input
#if defined(USE_USB_BUS_SENSE_IO)
#define usb_bus_sense PORTAbits.RA1
#else
#define usb_bus_sense 1
#endif
#define tris_self_power TRISAbits.TRISA2 // Input
#if defined(USE_SELF_POWER_SENSE_IO)
#define self_power PORTAbits.RA2
#else
#define self_power 1 // Used by USBStdGetStatusHandler() in usb9.c
#endif
// External Transceiver Interface
#define tris_usb_vpo TRISBbits.TRISB3 // Output
#define tris_usb_vmo TRISBbits.TRISB2 // Output
#define tris_usb_rcv TRISAbits.TRISA4 // Input
#define tris_usb_vp TRISCbits.TRISC5 // Input
#define tris_usb_vm TRISCbits.TRISC4 // Input
#define tris_usb_oe TRISCbits.TRISC1 // Output
#define tris_usb_suspnd TRISAbits.TRISA3 // Output
/** L E D ***********************************************************/
//#define mInitAllLEDs() LATD &= 0xF0; TRISD &= 0xF0;
#define mInitAllLEDs() LATC &= 0xF0; TRISC &= 0xF0; // 18F2550用に修正
//#define mLED_1 LATDbits.LATD0 // PIC 18F4550用
//#define mLED_2 LATDbits.LATD1
//#define mLED_3 LATDbits.LATD2
//#define mLED_4 LATDbits.LATD3
#define mLED_1 LATCbits.LATC0 // 18F2550用に修正
#define mLED_2 LATCbits.LATC1
#define mLED_3 LATCbits.LATC2
//#define mLED_4 LATCbits.LATC3 // 18F2550用はLATC3は無い。
#define mLED_1_On() mLED_1 = 1;
#define mLED_2_On() mLED_2 = 1;
#define mLED_3_On() mLED_3 = 1;
//#define mLED_4_On() mLED_4 = 1; // 18F2550用はLED4は使わない。
#define mLED_1_Off() mLED_1 = 0;
#define mLED_2_Off() mLED_2 = 0;
#define mLED_3_Off() mLED_3 = 0;
//#define mLED_4_Off() mLED_4 = 0; // 18F2550用はLED4は使わない。
#define mLED_1_Toggle() mLED_1 = !mLED_1;
#define mLED_2_Toggle() mLED_2 = !mLED_2;
#define mLED_3_Toggle() mLED_3 = !mLED_3;
//#define mLED_4_Toggle() mLED_4 = !mLED_4; // 18F2550用はLED4は使わない。
/** S W I T C H *****************************************************/
#define mInitAllSwitches() TRISBbits.TRISB4=1;TRISBbits.TRISB5=1;
#define mInitSwitch2() TRISBbits.TRISB4=1;
#define mInitSwitch3() TRISBbits.TRISB5=1;
#define sw2 PORTBbits.RB4
#define sw3 PORTBbits.RB5
/** P O T ***********************************************************/
#define mInitPOT() TRISAbits.TRISA0=1;ADCON0=0x01;ADCON2=0x3C;
/** S P I : Chip Select Lines ***************************************/
#define tris_cs_temp_sensor TRISBbits.TRISB2 // Output
#define cs_temp_sensor LATBbits.LATB2
#define tris_cs_sdmmc TRISBbits.TRISB3 // Output
#define cs_sdmmc LATBbits.LATB3
/** S D M M C *******************************************************/
#define TRIS_CARD_DETECT TRISBbits.TRISB4 // Input
#define CARD_DETECT PORTBbits.RB4
#define TRIS_WRITE_DETECT TRISAbits.TRISA4 // Input
#define WRITE_DETECT PORTAbits.RA4
/********************************************************************/
/********************************************************************/
/********************************************************************/
#elif defined(PIC18F87J50_FS_USB_PIM)
/** U S B ***********************************************************/
// Bus sense pin is RB5 on PIC18F87J50 FS USB Plug-In Module.
// Must put jumper JP1 in R-U position to use bus sense feature.
#define tris_usb_bus_sense TRISBbits.TRISB5 // Input
#if defined(USE_USB_BUS_SENSE_IO)
#define usb_bus_sense PORTBbits.RB5
#else
#define usb_bus_sense 1
#endif
#define self_power 0
/** L E D ***********************************************************/
#define mInitAllLEDs() LATE &= 0xFC; TRISE &= 0xFC;
#define mLED_1 LATEbits.LATE1
#define mLED_2 LATEbits.LATE0
#define mLED_1_On() mLED_1 = 1;
#define mLED_2_On() mLED_2 = 1;
#define mLED_1_Off() mLED_1 = 0;
#define mLED_2_Off() mLED_2 = 0;
#define mLED_1_Toggle() mLED_1 = !mLED_1;
#define mLED_2_Toggle() mLED_2 = !mLED_2;
/** S W I T C H *****************************************************/
#define mInitAllSwitches() TRISBbits.TRISB4=1;
#define mInitSwitch2() TRISBbits.TRISB4=1;
#define sw2 PORTBbits.RB4
/********************************************************************/
/********************************************************************/
/********************************************************************/
//Uncomment below if using the YOUR_BOARD hardware platform
#elif defined(YOUR_BOARD) // 2011/12/6 コメントアウトを外す
//Add your hardware specific I/O pin mapping here
// 2011/12/6 以下に #if defined(PIC18F4550_PICDEM_FS_USB) の記述をコピー
/** U S B ***********************************************************/
#define tris_usb_bus_sense TRISAbits.TRISA1 // Input
#if defined(USE_USB_BUS_SENSE_IO)
#define usb_bus_sense PORTAbits.RA1
#else
#define usb_bus_sense 1
#endif
#define tris_self_power TRISAbits.TRISA2 // Input
#if defined(USE_SELF_POWER_SENSE_IO)
#define self_power PORTAbits.RA2
#else
#define self_power 1 // Used by USBStdGetStatusHandler() in usb9.c
#endif
// External Transceiver Interface
#define tris_usb_vpo TRISBbits.TRISB3 // Output
#define tris_usb_vmo TRISBbits.TRISB2 // Output
#define tris_usb_rcv TRISAbits.TRISA4 // Input
#define tris_usb_vp TRISCbits.TRISC5 // Input
#define tris_usb_vm TRISCbits.TRISC4 // Input
#define tris_usb_oe TRISCbits.TRISC1 // Output
#define tris_usb_suspnd TRISAbits.TRISA3 // Output
/** L E D ***********************************************************/
//#define mInitAllLEDs() LATD &= 0xF0; TRISD &= 0xF0;
#define mInitAllLEDs() LATC &= 0xF0; TRISC &= 0xF0; // 18F2550用に修正
//#define mLED_1 LATDbits.LATD0 // PIC 18F4550用
//#define mLED_2 LATDbits.LATD1
//#define mLED_3 LATDbits.LATD2
//#define mLED_4 LATDbits.LATD3
#define mLED_1 LATCbits.LATC0 // 18F2550用に修正
#define mLED_2 LATCbits.LATC1
#define mLED_3 LATCbits.LATC2
//#define mLED_4 LATCbits.LATC3 // 18F2550用はLATC3は無い。
#define mLED_1_On() mLED_1 = 1;
#define mLED_2_On() mLED_2 = 1;
#define mLED_3_On() mLED_3 = 1;
//#define mLED_4_On() mLED_4 = 1; // 18F2550用はLED4は使わない。
#define mLED_1_Off() mLED_1 = 0;
#define mLED_2_Off() mLED_2 = 0;
#define mLED_3_Off() mLED_3 = 0;
//#define mLED_4_Off() mLED_4 = 0;
#define mLED_1_Toggle() mLED_1 = !mLED_1;
#define mLED_2_Toggle() mLED_2 = !mLED_2;
#define mLED_3_Toggle() mLED_3 = !mLED_3;
//#define mLED_4_Toggle() mLED_4 = !mLED_4; // 18F2550用はLED4は使わない。
/** S W I T C H *****************************************************/
#define mInitAllSwitches() TRISBbits.TRISB4=1;TRISBbits.TRISB5=1;
#define mInitSwitch2() TRISBbits.TRISB4=1;
#define mInitSwitch3() TRISBbits.TRISB5=1;
#define sw2 PORTBbits.RB4
#define sw3 PORTBbits.RB5
/** P O T ***********************************************************/
#define mInitPOT() TRISAbits.TRISA0=1;ADCON0=0x01;ADCON2=0x3C;
/** S P I : Chip Select Lines ***************************************/
#define tris_cs_temp_sensor TRISBbits.TRISB2 // Output
#define cs_temp_sensor LATBbits.LATB2
#define tris_cs_sdmmc TRISBbits.TRISB3 // Output
#define cs_sdmmc LATBbits.LATB3
/** S D M M C *******************************************************/
#define TRIS_CARD_DETECT TRISBbits.TRISB4 // Input
#define CARD_DETECT PORTBbits.RB4
#define TRIS_WRITE_DETECT TRISAbits.TRISA4 // Input
#define WRITE_DETECT PORTAbits.RA4
#else
#error Not a supported board (yet), add I/O pin mapping in __FILE__, line __LINE__
#endif
#endif //IO_CFG_H